感应门是一种能够实现自动感应识别开关功能的感应门。其原理是通过内部感应探测器检测是否有人进入，结构合理的手术室感应门，为医院和实验室提供了大大的便利。感应门的使用需要达到良好的效果，这不仅与它的质量有关，还与它的安装有关。如果安装不正确，会导致后期出现很多问题。下面济南感应门厂家为您分析：

Induction gate is a type of induction gate that can achieve automatic induction recognition switch function. The principle is to detect whether someone has entered through an internal sensing detector, and a structurally reasonable operating room sensing door provides great convenience for hospitals and laboratories. The use of induction doors needs to achieve good results, which is not only related to their quality, but also to their installation. If installed incorrectly, it can lead to many problems later on. Below is an analysis by the Jinan sensory door manufacturer for you:

一、安装医用感应门电机时，注意使之保持水平，保持误差小于一毫米，如果不在一条水平线上会影响导致门体行走时没有出现力道不均匀的现象，造成摩损严重，从而使之寿命不断降低。

1、 When installing the medical induction door motor, pay attention to keeping it horizontal, with an error of less than one millimeter. If it is not on the same horizontal line, it will affect the phenomenon of uneven force path when the door body walks, causing serious friction damage and continuously reducing its lifespan.

二、手术室感应门吊架的安装，使用所附的门吊架螺栓总成将吊架装置安装到门上的指定位置。安装时，吊架装置的滑轮中心应与门体平行。如果不平行，会缩短滑轮的使用寿命；同时悬挂装置的滑轮悬挂在动力梁上，以免在安装过程中损坏动力梁中的其他部件和导轨，否则会导致部件故障或滑轮寿命、噪音、异常声音等。

2、 Install the operating room sensing door hanger using the attached door hanger bolt assembly to install the hanger device in the designated position on the door. When installing, the pulley center of the hanger device should be parallel to the door body. If not parallel, it will shorten the service life of the pulley; At the same time, the pulley of the suspension device is suspended on the power beam to prevent damage to other components and guide rails in the power beam during installation, otherwise it may cause component failure or pulley life, noise, abnormal sound, etc.

三、手术室自动感应门的限位装置应安装与限位装置相一致的安装螺栓。位置限制器装置固定在动力梁的导轨上，移动门体固定门体位置后，位置限制器的位置固定。设置限位器位置时，悬挂装置接触限位器橡胶垫时应停止。

3、 The limit device of the automatic sensing door in the operating room should be installed with bolts that are consistent with the limit device. The position limiter device is fixed on the guide rail of the power beam. After moving the door body to fix the position of the door body, the position of the position limiter is fixed. When setting the position of the limiter, the suspension device should stop when it contacts the rubber pad of the limiter.

四、适当松开固定吊架的螺母，调整手术室感应门体的高度和间隙。调整螺栓和固定吊架的目的是确认行走时的阻力，确保门移动时没有自重或摩擦声。如果有问题，请确认门体上的挂钩是否垂直固定。悬挂装置是否与动力梁有摩擦。

4、 Loosen the nuts securing the hanger appropriately, and adjust the height and clearance of the operating room sensing door body. The purpose of adjusting the bolts and fixing the hanger is to confirm the resistance during walking and ensure that there is no self weight or friction sound when the door moves. If there are any issues, please confirm whether the hooks on the door body are vertically fixed. Is there friction between the suspension device and the power beam.

五、注意提高手术室感应门的皮带张力调整。皮带张力结构调整应保证将张紧轮装置向左用力拉，使皮带保持绷紧状态。通过拧松手术室感应门的调节固定螺栓，沿顺时针方向以及旋转张力不断调整螺栓，同时没有拧紧四个方面调节板固定螺栓进而分析确定皮带是否正确的张力。

5、 Pay attention to adjusting the belt tension of the operating room sensing door. The adjustment of the belt tension structure should ensure that the tensioning wheel device is forcefully pulled to the left to keep the belt in a tight and safe state. By loosening the adjusting fixing bolts of the operating room sensing door, continuously adjusting the bolts in a clockwise direction and rotating the tension, while not tightening the four adjusting plate fixing bolts, the correct tension of the belt can be analyzed and determined.

手术室感应自动门的安装技巧相关内容就讲解到这里了，希望能够给您好的帮助，更多事项就来我们网站http://www.jnkdblgd.com咨询！

That's all for the installation techniques of the operating room induction automatic door. We hope to provide you with good help. For more information, please come to our website http://www.jnkdblgd.com consulting service