安装济南玻璃门时，先了解门的组件和门的类型，门的组件是门盖，门页，门锁，铰链和门触，根据其功能分类，包括平开门，推拉门，折叠门，弧形门等。下面小编来讲讲具体的步骤吧！

When installing Jinan glass door, first understand the components of the door and the type of the door. The components of the door are the door cover, the door leaf, the door lock, the hinge and the door contact. According to their functional classification, they include the swing door, sliding door, folding door, arc door, etc. Now let's talk about the specific steps!

1.定位，放线：玻璃门结合固定玻璃和活动玻璃门扇，统一定位。

1. Positioning and setting out: the glass door shall be positioned uniformly by combining fixed glass and movable glass door leaf.

2.安装框架顶部的限制槽：限制槽的宽度对于玻璃厚度应大于2-4mm，对于槽深度应大于10-20mm，安装时，从绘制的线上拉出两个金属装饰板边缘，然后按侧线，在门框顶部安装限位槽。

2. Install the limit slot on the top of the frame: the width of the limit slot shall be greater than 2-4mm for the glass thickness, and the depth of the slot shall be greater than 10-20mm. During installation, first pull out two metal trim panel edges from the drawn line, and then install the limit slot on the top of the door frame according to the side line.

3.在木质底部安装金属饰面：将方木固定在地面上，然后用胶将金属饰面粘在木头上，方木可直接钉在预嵌木砖上，或通过膨胀螺栓固定。

3. Install metal facing at the bottom of the wood: first fix the square wood on the ground, and then stick the metal facing to the wood with glue. The square wood can be directly nailed to the pre embedded wood brick, or fixed by expansion bolts.

4.安装垂直门框：将子弹的中心线连接到门框，然后用胶合板确定门框柱的形状和位置，后外包金属装饰面。

4. Install the vertical door frame: connect the center line of the bullet to the door frame, and then use plywood to determine the shape and position of the door frame column, and then wrap the metal decorative surface.

5.安装玻璃：用玻璃吸盘机吸入厚玻璃，然后握住吸盘将厚玻璃板抬起2-3人，移安装位置。

5. Installation of glass: use a glass suction cup machine to suck in thick glass, then hold the suction cup to lift the thick glass plate by 2-3 people and move it to the installation position.

6.固定玻璃：木块底部和侧面有两个小方形木条，厚玻璃夹在中间门上，方形木条距玻璃板表面约4mm，然后在方形木条上涂上通用胶将粘贴的金属粘在方形条上。

6. Fixed glass: there are two small square wooden strips at the bottom and side of the wooden block, the thick glass is clamped on the middle door, and the square wooden strip is about 4mm from the surface of the glass plate, and then apply universal glue on the square wooden strip to stick the pasted metal on the square strip.

7.注塑玻璃密封：在顶部限位槽和底部支架的两侧，以及厚玻璃和框架柱等之间的间隙，进入玻璃密封。

7. Injection moulded glass seal: enter the glass seal at both sides of the top limit slot and the bottom bracket, as well as the gap between the thick glass and the frame column.

8.玻璃之间的对接：当玻璃门固定部分需要大尺寸拼接时，接缝宽度应为2-3mm，玻璃板边缘应倒角。

8. Butt joint between glasses: When the fixed part of the glass door needs to be spliced in large size, the joint width should be 2-3mm, and the glass plate edge should be chamfered.

9.移动玻璃门安装：在安装门扇之前，应定位和安装接地弹簧和门框顶面上的定位销，两者须是同轴的，安装时，使用垂直线检查以确保接地弹簧轴和定位销的中心线在同一直线上。

9. Installation of movable glass door: before installing the door leaf, the grounding spring and the locating pin on the top surface of the door frame shall be positioned and installed. Both must be coaxial. During installation, the vertical line shall be used to check to ensure that the center line of the grounding spring shaft and the locating pin is on the same straight line.

10.安装玻璃门扇上下门夹：在玻璃门的上下两端安装上下金属门夹，测量门高。

10. Installation of upper and lower door clips of glass door leaf: install upper and lower metal door clips at upper and lower ends of glass door, and measure the door height.

要注意，在开始所有安装步骤之前，须确保在施工完成之前基本完成室内装饰和装饰的其他过程，并且应严格定位对齐按照设计图纸。更多相关内容就来我们网站http://www.jnkdblgd.com咨询吧！

It should be noted that before starting all the installation steps, it is necessary to ensure that the interior decoration and other processes of decoration are basically completed before the completion of construction, and the alignment should be strictly in accordance with the design drawings. More relevant content will come to our website http://www.jnkdblgd.com Consult!