高隔间的安装方法是怎样的呢？下面就来看看相关的内容吧。

　　What is the installation method of high compartment? Here's a look at the relevant content.

　　根据施工图示结合实地的测量，从地龙骨内天龙骨下边线尺寸，减15毫米20毫米为竖龙骨实际切割尺寸。把竖龙骨两端插入直角连接件，放入地龙骨槽内，搭接天龙骨，把天、地龙骨与连接件用顶丝固定，竖龙骨与天龙骨缝隙不大于5毫米，与门框相连接的两侧竖龙骨是落地安装。

　　According to the construction diagram combined with the field measurement, the actual cutting size of the vertical keel is 15 mm to 20 mm from the inside of the ground keel to the lower edge of the sky keel. Insert both ends of the vertical keel into the right Angle connector, into the keel slot, lap to the day keel, the day, the ground keel and the connector fixed with the top wire, the gap between the vertical keel and the day keel is not greater than 5 mm, and the door frame is connected on both sides of the vertical keel is ground installation.

　　根据图纸和实地放线位置，把门和转角的位置预留，地龙骨用胀栓固定于地坪上以螺丝固定地龙骨固定点间隔约一千毫米，需先在两端约一百毫米位置固定。用墨斗线或水准仪在竖龙骨上确定横龙骨安装位置。把横龙骨两端插入直角连接件，放入左右竖龙骨之间调整所需上下间隔尺寸。

　　According to the drawings and the location of the field line, the location of the door and corner is reserved, and the keel is fixed on the floor with φ6 expansion bolt to fix the keel with screws at an interval of about one thousand millimeters, which needs to be fixed at both ends at about one hundred millimeters. Use ink line or level to determine the installation position of the horizontal keel on the vertical keel. Insert both ends of the horizontal keel into the right Angle connector, put it between the left and right vertical keel to adjust the required upper and lower spacing size.

　　安装天龙骨扣条，把扣条扣在天龙骨两面，用橡皮锤敲击扣条，使扣条扣入天龙骨槽内。接缝处要紧密，注意扣条拼接处位置要合理、协调。然后，安装竖龙骨扣条。测量地龙骨上边线天龙骨扣条下边线尺寸，要求切割尺寸，采用凸起带槽扣条或凸起平板扣条。把扣条扣在竖龙骨两面，用橡皮锤敲击扣条，使扣条扣入竖龙骨槽内，拼缝处缝隙不得大于0.3毫米。带槽扣条可根据需要中间插装装饰条。

　　Install the keel buckle, buckle the buckle on both sides of the keel, hit the buckle with a rubber hammer, make the buckle buckle into the keel slot. Joints should be close, pay attention to buckle splicing position should be reasonable and coordinated. Then, install the vertical keel buckle. Measure the size from the upper edge of the keel to the lower edge of the keel buckle. Cut the size according to the requirements. Use raised buckle with groove or raised flat buckle. Buckle the buckles on both sides of the vertical keel, and hit the buckles with a rubber hammer to make the buckles fit into the vertical keel slot. The gap between the seams should not be greater than 0.3mm. Slotted buckle can be inserted in the middle of the trim as required.

　　济南高隔间系统安装程序：安装一侧面板→配合交叉作业→放置岩棉→安装另一侧面板实体面板安装(饰面石膏板、装饰布和三聚氰胺饰面板)装饰布饰面需用纸面石膏板板(8毫米9毫米厚)，采用胶把布平整粘贴后热压处理，用钢制订书钉把装饰布边在面板背面固定。木质板材用电切割锯裁切好。

　　Ji 'nan high compartment system installation procedures: Install the side panel - work between cross - put the rock wool - another side panel entities panel installation (veneer gypsum board, decorating and melamine veneer) decorative veneer need gypsum board plate (8 mm to 9 mm thick), using environmental protection rubber cloth paste level off after extrusion processing, steel making staple the vestee edge fixed on the back panel. Wood plate cut with electric cutting saw.

　　高隔间的安装方法有几个大步骤便是以上内容了，如果您有什么不理解的就来网站www.jnkdblgd.com咨询吧。

　　There are several big steps in the installation method of high compartment is the above content, if you do not understand what to consult the website www.jnkdblgd.com.