安装玻玻璃墙、门顶部限位槽的宽度应大于玻璃厚度2～4mm，槽深在20～30mm之间，以便注胶。济南玻璃隔断墙分享安装方法可由所弹线引出两条金属装饰板边线，然后按边线进行门框顶部限位槽的安装。槽口内的木垫板是调整槽深的。通过垫板的增多或减少调整。

The width of the limit groove at the top of the glass wall and door shall be 2~4mm greater than the glass thickness, and the groove depth shall be 20~30mm for the convenience of glue injection. The shared installation method of Jinan glass partition wall can draw two metal decorative panel sidelines from the snapped line, and then install the limit slot at the top of the door frame according to the sidelines. The wooden backing plate in the groove is used to adjust the groove depth. Adjust by increasing or decreasing the base plate.

济南玻璃安装金属饰面的木底托。安装方法可在原预埋木砖上钉方木，或通过膨胀螺栓钉方木，把方木固定在地面上，然后再用***胶将金属饰面板粘在木方上。铝合金方管，可用铝角固定在框柱上，或用木螺钉固定在埋入地面中的木砖上。

Jinan glass is installed with metal veneer wooden base. The installation method can be nailing the square timber on the original embedded wooden brick, or nailing the square timber with expansion bolts to fix the square timber on the ground, and then using all-purpose adhesive to stick the metal decorative panel on the wooden block. The aluminum alloy square tube can be fixed on the frame column with aluminum angle or on the wooden brick embedded in the ground with wood screws.

安装坚向门框。按所弹线钉立门框方木，然后用胶合板确定门框柱的外形尺寸和位置的固定（注意应减除装饰面尺寸）。后外包金属装饰面，包时要把饰面对头接缝放置在安装玻璃的两侧中间位置。接缝位置必须准确并保证垂直。

Install the rigid door frame. Nail the square timber of the door frame according to the snapped line, and then use plywood to determine the overall size and position of the door frame column (note that the size of the decorative surface should be deducted). The back shall be wrapped with metal decorative surface, and the facing butt joint shall be placed in the middle of both sides of the installation glass. The joint position must be accurate and vertical.

玻璃安装。用玻璃吸盘器（或玻璃吸盘机）把厚玻璃吸紧吸住，然后手握吸盘把通过2～3人把厚玻璃板抬起并竖立起来移安装地点准备就位。就位方法：应把玻璃上部插入门框顶部的限位槽内，然后把玻璃的下部放到底托上对正线，并对好两侧门框的安装位置，使厚玻璃的两侧边部正好封住门框的金属饰面对缝口，要求做到内外都看不见饰面接缝口

Glass installation. Use a glass suction cup (or glass suction cup machine) to suck the thick glass tightly, and then hold the suction cup handle to lift and erect the thick glass plate through 2 to 3 people and move it to the installation site for preparation. Positioning method: insert the upper part of the glass into the limit slot on the top of the door frame, then put the lower part of the glass on the bottom bracket and align the installation position of the door frame on both sides, so that the two sides of the thick glass can just seal the metal facing butt joint of the door frame, and it is required to make the facing seam invisible both inside and outside

玻璃固定。在底托木上的内外钉两根扁方木条把厚玻璃夹在中间，但距厚玻璃板需留出4mm左右的空隙，然后在扁方木条上涂刷***胶将饰面金属板粘卡在方木和两根扁方木条上。

Glass fixation. Nail two square battens on the inside and outside of the bottom joist to clamp the thick glass in the middle, but leave a gap of about 4mm from the thick glass plate, and then apply all-purpose adhesive on the square batten to stick the decorative metal plate on the square wood and two square battens.

注玻璃胶封口。在顶部根位槽两侧空隙内和底托玻璃槽口的两侧以及厚玻璃与门框柱的对缝处注入玻璃胶。注入顺序应从某一条缝隙的端头开始到末端终止，中途不得停顿。操作要领是：握紧嵌缝枪压柄用力要均匀，同时顺着缝隙移动的速度也要均匀，即随着玻璃胶的挤出，匀速移动注胶口，使玻璃胶在缝隙处形成一条均匀的直线。后用塑料片刮去多余的玻璃胶并用干净布擦去胶

Seal with glass glue. Inject glass glue into the gap on both sides of the top root slot, both sides of the bottom glass slot and the butt joint between the thick glass and the door frame column. The injection sequence shall start from the end of a gap to the end, and shall not stop halfway. The key points of operation are: hold the caulking gun pressure handle with even force, and move along the gap with even speed, that is, with the extrusion of the glass glue, move the glue injection port at a uniform speed, so that the glass glue forms a uniform straight line at the gap. After that, scrape off the excess glass glue with a plastic sheet and wipe off the glue with a clean cloth

玻璃之间对接。固定部分的厚玻璃板，由于宽度尺寸过大，必须用两块或两块以上进行拼装而成，两块对齐拼接必然形成接缝，对接缝应留2～3mm的距离（对接缝的玻璃切口必须倒用）。玻璃固定后，要用玻璃胶入缝隙中，注满后同样要用塑料片把胶刮平，使缝隙形成一条洁净的均匀直线，玻璃面上要用干净布擦净胶迹。

Butt joint between glass. The thick glass plate of the fixed part must be assembled with two or more pieces due to its large width. The two pieces must be aligned and spliced to form a joint. A distance of 2~3mm should be reserved for the joint (the glass cut of the joint must be reversed). After the glass is fixed, the glass glue shall be inserted into the gap, and the plastic sheet shall also be used to scrape the glue flat after filling, so that the gap forms a clean and uniform straight line, and the glue mark on the glass surface shall be wiped with a clean cloth.

以上就是济南玻璃安装厂家分享的阳台玻璃窗安装方法的知识问题讲解，相信大家看了以后应该会有更多的认识了吧，内容仅供大家参考，有不懂的问题就来咨询我们http://www.jnkdblgd.com吧！

The above is the explanation of the knowledge of the installation method of balcony glass windows shared by Jinan glass installation manufacturers. I believe you will have more understanding after reading it. The content is for your reference only. If you don't understand the problem, please consult us http://www.jnkdblgd.com Come on!