玻璃门安装相比其他材质门安装更为复杂，玻璃门安装工程要十分小心和注意，这样可以有效的避免造成一些不必要的伤害。下面来讲讲济南玻璃门安装前准备工作以及安装施工事项吧。

The installation of glass doors is more complicated than that of other materials. The installation of glass doors should be very careful and careful, which can effectively avoid causing unnecessary injuries. Now let's talk about the preparatory work before the installation of Jinan glass doors and the installation and construction matters.

安装前准备工作

Preparation before installation

玻璃门安装前，保证地面施工已完毕，不锈钢或其它饰面门框已完毕。厚玻璃限位槽已留出。一定要非常小心四个角位的倒角一通常情况应用手握细砂轮块，缓慢进行磨角，以防崩边崩角。不锈钢饰面的木底托，应用木楔钉的方法固定在地面。之后可用***胶将不锈钢饰面板粘卡在木方上。铝合金方管可用铝角固定在框柱上，或用木螺钉固定于地面埋入的木楔上。

Before the installation of glass doors, ensure that the ground construction has been completed and the stainless steel or other decorative door frames have been completed. Thick glass limit groove has been reserved. Be very careful with the chamfering of the four corners. Generally, hold the fine grinding wheel and grind the corners slowly to prevent edge collapse. The wooden bottom bracket with stainless steel facing shall be fixed on the ground by means of wood wedge nails. After that, the stainless steel decorative panel can be stuck on the wooden square with universal glue. The aluminum alloy square tube can be fixed on the frame column with aluminum angle, or fixed on the wood wedge embedded in the ground with wood screws.

安装施工

Installation construction

先用玻璃吸盘器把厚玻璃吸紧，再手握吸盘器把厚玻璃板抬起。抬起时需要2－3人同时进行。抬起后的厚玻璃板，插入门框顶部的限位槽内，再放到底托上，并对好安装位置，使厚玻璃板的边部，正好封住侧框柱的不锈钢饰面对缝口。

First, use the glass sucker to hold the thick glass tightly, and then hold the sucker to lift the thick glass plate. Two to three people are required to lift at the same time. After lifting the thick glass plate, insert it into the limit slot at the top of the door frame first, then place it on the bottom bracket, and align the installation position so that the edge of the thick glass plate can just seal the stainless steel facing seam of the side frame column.

先将玻璃胶打开装入玻璃胶注射枪，再用玻璃胶枪的后压杆端头板，这样便可顶住玻璃胶罐的底部。用手托住玻璃胶注射枪身一只手握着注胶压柄，并不断松、压循环地操作压柄，挤出少量的玻璃胶注入。再把玻璃胶的注口对准缝隙端封口。

First open the glass glue and load it into the glass glue injection gun, and then use the rear pressing rod end plate of the glass glue gun to support the bottom of the glass glue tank. Hold the glass glue injection gun body with one hand and hold the glue injection handle, and operate the handle continuously and cyclically to squeeze out a small amount of glass glue injection. Then align the injection of glass glue with the gap end for sealing.

固定部分的厚玻璃板，往往不可用一块来完成。在厚玻璃对接时，注意对接缝隙要在2-3mm之间，厚玻璃边需倒角。两块相接的厚玻璃定位并固定后，用玻璃胶注入缝隙中，注满之后用塑料片在厚玻璃的两面刮平玻璃胶，用净布擦去胶迹。

The fixed part of the thick glass plate can not be completed by one piece. During butt joint of thick glass, the butt joint gap shall be 2-3mm, and the thick glass edge shall be chamfered. After the two thick glasses connected are positioned and fixed, the glass glue is injected into the gap. After filling, the plastic sheet is used to scrape the glass glue on both sides of the thick glass, and the glue mark is wiped off with a clean cloth.

消费者在选择玻璃门的时侯也有一些方法，不但要掌握方法，还需要注意安装过程中出现的问题，如果不知道自己装修以后是什么效果，那么可以通过选择玻璃门图片来完成，这样就可以得到很多的优势。更多相关事项就来我们网站http://www.jnkdblgd.com进行咨询吧！

Consumers also have some methods when choosing glass doors. They should not only master the methods, but also pay attention to the problems in the installation process. If they do not know what the effect is after their own decoration, they can choose the pictures of glass doors to complete, so they can get a lot of advantages. Come to our website for more information http://www.jnkdblgd.com Consult!