At present, most offices use partition doors, so the use of glass partition doors is gradually increasing, and the natural sales volume is also increasing. But many people are curious and want to know glass partition door, glass sliding door, glass high compartment Installation methods of various glass doors and some precautions during installation. Let's talk about the installation methods and precautions of various glass doors for you!

济南玻璃门摆设门径：

Jinan glass door decoration door diameter:

1、 定位、放线：由静止玻璃与勾当玻璃门扇组合玻璃门，差异进行放线定位，遵循整治和施工图纸需求，放出玻璃门的定位线，一起鉴定门框方位。

1. Positioning and setting out: set out and locate the glass door by combining the static glass and the active glass door leaf. Set out the positioning line of the glass door and identify the orientation of the door frame together in accordance with the requirements of the rectification and construction drawings.

2、 摆设框顶部限位槽：限位槽的宽应大于玻璃厚度二四毫米,槽深为十二十毫米。装置时，一***由所弹中凡线引出两条金属装修板边线，接着按边线进行门框顶部限位槽的摆设，经由胶合垫板斡旋槽口内的槽深。

2. Limit groove at the top of the display frame: the width of the limit groove shall be 2-4 mm greater than the glass thickness, and the groove depth shall be 10-20 mm. When installing the device, one first leads out two metal decoration board sidelines from the middle line, then arranges the limit groove at the top of the door frame according to the sideline, and mediates the groove depth in the groove through the glued base plate.

3、 装置金属饰面的木底托：把方木固定在地上上，用***胶把金属饰面板粘在木上。若选用铝合金方管，兴许用铝角固定在框柱上，或用木螺钉固定在埋入地上中的木砖上。

3. Wooden bottom support with metal finish: fix the square wood on the ground, and stick the metal decorative panel to the wood with universal glue. If aluminum alloy square pipe is selected, it may be fixed on the frame column with aluminum angle or on the wooden brick embedded in the ground with wood screws.

4、 装置竖向门框：接所弹外围线钉立门框方木，接着用胶合板断定门框柱的状态和方位，终外包金属装修面。包饰面时要把饰面仇敌接缝方位放在装置玻璃的中间中门方位。

4. Installation of vertical door frame: connect the snapped peripheral line to nail the square wood of the door frame, then determine the state and orientation of the door frame column with plywood, and finally wrap the metal decoration surface. When wrapping the veneer, the joint direction of the veneer shall be placed in the middle door direction of the device glass.

5、 装置玻璃：用玻璃吸盘机把厚玻璃吸紧，把厚玻璃板抬起移摆设方位。先把玻璃上部刺进门框顶部的限位槽，再把把玻璃的下部放终于托上。

5. Glass installation: use the glass suction cup machine to suck the thick glass tightly, lift the thick glass plate and move it to the layout direction. Stab the upper part of the glass into the limit slot at the top of the door frame, and then put the lower part of the glass on the support.

6、 静止玻璃：在底托方木上的表里钉两根小方木条把厚玻璃夹在中门，在方木条上涂刷全能胶并把饰面金属粘在在方木条上。

6. Static glass: nail two small square wood strips on the surface and inside of the square wood on the bottom support, clamp the thick glass on the middle door, brush all-round glue on the square wood strip, and stick the facing metal on the square wood strip.

7、 注玻璃胶封口：在顶部限位槽与底部托槽口的两头，以及厚玻璃与框柱的对缝处等各缝隙处，写入玻璃胶封口，用工具刮去残余的玻璃胶。

7. Note: glass glue sealing: write glass glue sealing at the two ends of the top limit groove and the bottom bracket mouth, as well as the butt joint between thick glass and frame column, and scrape off the residual glass glue with tools.

8、 玻璃对接：玻璃门静止有些因尺寸过大而需要拼接时，其对缝要有二三毫米的宽度，玻璃板边要发展倒角措置。

8. Glass butt joint: when the glass door is still and needs to be spliced due to its large size, the butt joint should have a width of 2-3mm, and the edge of the glass plate should be chamfered.

9、 地弹簧摆设：门扇装置前地上地弹簧与门框顶面的定位销应装置结束何况有重要同轴线，摆设时***用吊垂线检查确保在同不绝线上。

9. Floor spring arrangement: the floor spring in front of the door leaf device and the locating pin on the top surface of the door frame should be installed at the end. In addition, there is an important coaxial line. During the arrangement, it is best to check with a hanging vertical line to ensure that it is on the same continuous line.

10、 摆设凹凸门夹：把凹凸金属门夹离别装在玻璃门扇上下中间，假设门扇高度缺乏，可鄙人门夹内玻璃底部垫木夹板条。

10. Furnishing concave convex door clamp: install concave convex metal door clamp separately in the upper and lower middle of glass door leaf. Assuming that the door leaf is lack of height, the bottom of glass in the door clamp is padded with wooden splint strip.

11、 固定玻璃门门夹：定好门扇高度后，在玻璃与凹凸门夹内的中间缝隙刺进小木条，在缝隙中写入玻璃胶固定。

11. Fixing the glass door clip: after setting the height of the door leaf, stab a small wooden strip into the middle gap between the glass and the concave convex door clip, and write glass glue in the gap for fixing.

12、 门扇摆设：先把定位销用自己的疗养螺钉调出横梁立体二毫米，把单元玻璃门扇竖起来，门扇下门夹内的转动销联接件的孔位对准地弹簧的动弹销轴，转动门扇把孔位套入 销轴上，把门扇迁移转变与门框横梁成直角，把门扇上门夹中的转折联接件孔对准门框横梁上的定位销，调节定位销的调治螺钉，把定位销刺进孔内。

12. Door leaf decoration: first, pull out the positioning pin with its own convalescent screw to the three-dimensional 2mm of the cross beam, erect the unit glass door leaf, align the hole position of the rotating pin connector in the door clamp under the door leaf with the dynamic pin shaft of the ground spring, rotate the door leaf, put the hole position on the pin shaft, and move the door leaf to form a right angle with the cross beam of the door frame, Align the turning connector hole in the door clamp of the door leaf with the locating pin on the door frame beam, adjust the adjusting screw of the locating pin, and pierce the locating pin into the hole.

13、 拉手摆设：摆设前在拉咭片进玻璃的有些涂少量玻璃胶，拉手装配时根部与玻璃靠紧密后再按紧静止螺钉，以确保拉手没有松动征兆。

13. Handle arrangement: before the arrangement, apply a small amount of glass glue to some of the parts that pull the card into the glass. When the handle is assembled, the root is close to the glass, and then press the static screw to ensure that the handle is not loose.

济南玻璃门装置留意变乱：

Attention to the accident of Jinan glass door device:

1、装置玻璃门前，要检查门窗扇是不是平整，预留孔眼是否是彻底、粗略，要是不适宜需求的就应当先校订。

1. Before installing the glass door, check whether the door and window leaves are flat and whether the reserved holes are thorough and rough. If they are not suitable for the needs, they should be revised first.

2、装置钢框、门扇玻璃应用钢丝卡固定，隔断不得大于300妹妹，且每边许多于两个，也也许以在钢丝卡上抹油灰面层，以增加密封性。

2. The steel frame and door leaf glass of the device shall be fixed with steel wire clamp, and the partition shall not be greater than 300 meters, and there are more than two on each side, or the putty surface layer may be applied on the steel wire clamp to increase the tightness.

3、如用油灰固定，则油灰应填实抹光。如用橡皮垫，应先将橡皮垫嵌入，并用压条与螺钉静止。

3. If it is fixed with putty, the putty shall be filled and troweled. If a rubber pad is used, the rubber pad shall be embedded first, and the pressure strip and screw shall be used to stand still.

4、如选用压条静止，通常在四边或两端加压条，用密封胶封好。

4. If the pressure strip is selected to be static, the pressure strip is usually added on four sides or both ends and sealed with sealant.

5、装置种种募捐质料要合适企图需乞降有关尺度规定。

5. The installation of various fund-raising materials should be appropriate, and the relevant standards and regulations need to be lowered.

6、组装彩色玻璃、区花玻璃时，应与筹画丹青相符，不得错位、斜曲和松动，玻璃的朝向应相宜规画需求。

6. When assembling colored glass and area patterned glass, it shall be consistent with the planned Danqing, and shall not be misplaced, skewed and loose. The orientation of the glass shall meet the planning requirements.

以上是由济南凯达玻璃为大家整理出来的一些玻璃门安装方法和安装时的注意事项，希望通过以上内容的分析和了解能够真正帮到你。

The above are some installation methods and precautions for glass doors sorted out by Jinan Kaida glass. I hope the analysis and understanding of the above contents can really help you.